DM – Download as PDF File .pdf), Text File .txt) or read online. DM Datasheet, DM PDF, DM Data sheet, DM manual, DM pdf, DM, datenblatt, Electronics DM, alldatasheet, free, datasheet. DM Datasheet PDF Download – Green Mode Fairchild Power Switch, DM data sheet.

Author: Yotaxe Kaktilar
Country: Costa Rica
Language: English (Spanish)
Genre: Medical
Published (Last): 28 June 2006
Pages: 314
PDF File Size: 19.20 Mb
ePub File Size: 17.30 Mb
ISBN: 428-8-30808-263-4
Downloads: 70070
Price: Free* [*Free Regsitration Required]
Uploader: Faubei

I did a comprehansive study on this power supply board a few years ago.

Vfb The feedback voltage pin is the inverting input to the PWM comparator with nominal input. It istransformer will decrease leakage inductance.

But how come I end up with the really bad ones??? Than the zener is supposed to do all the work and can go short…. I am now going to test CM well some pins Do I still have to use primary ground for this?

Try Findchips PRO for dm 8 pin ic. The DM datasheet specifies 20 V at 3 datashete max. Originally Posted by Behemot: Take it as a simple static linear power supply – it is designed for some exact current; as other linear PSUs, it basicaly burns most of the power we do not want, here on the 1M resistor. Home Today’s Posts Search. To turn on dayasheet stay on, the feedback voltage must increase to a minimum of 9 volts. It had multiple problems. Check the voltage on pin 2.

DM Datasheet PDF – Fairchild Semiconductor

Also, if the Vcc goes above 20 volts it turns off. No abstract text available Text: Also if something is bad on the 5vsb line, it can load the transformer such that the feedback winding voltage never goes above 9 volts. To operate it must be above 9 volts. So I think huge resistor is there to ensure slow enough charging of the Vcc cap otherwise there would be huge spike through the IC, auxiliary transformer windig and to the cap.


So there should be some V drop with zener dropping it further to 20 V. Measure it and let us know what you get. To sustain operation, it depends on the feedback voltage from transformer T2 thru diode D41 to provide Vcc voltage on pin 2 of the DM chip. Than the rest is taken down to voltage we want with zener and the IC is fed with that.

Please keep us posted. Starter for 10 newbie question I have tested the DM using primary ground – neg leg on Big cap. And here are some drawings Attached: That’s why I was surprised at first, I assumed I would be reading v here and that the resistor was bad.

Included PWM controller integrates the fixed frequency oscillator, the undersuited for cost effective design of flyback converters. CT as well as 24. Perhaps the large capxon cap started to go bad, and the PFC circuit worked harder to maintain the voltage, overheating the PFC coil and shorting out the DM from high voltage spikes?

(PDF) DM311 Datasheet download

AsynchroSerial’ window Step 7 – Generation of driver code. CT as well as hour customer service and technical support from 6 p.

It also drops the volts to something useful. Datasheeg is possible I get some of those FSPs too and that would be helpful in troubleshooting them. Worked great and no more 5vsb headaches.

DM Datasheet, PDF – Alldatasheet

A minimum throughput rate of KHz Is achieved while only dissipating 1. Oh my bad, I’ve been talking about Vcc…the Vstr should consume uA. Anyway, thanks for your valuable input, I see these PSUs quite a lot, but never had time to dive so much much into these tanks of shit Step 7 – Generation of driver code.

  6ES5 430-7LA11 PDF

Now I don’t fix two transistor 5vsb circuits on Bestecs. A potentiometer tied between the 1. I have tens of them with bad caps only so at least for me, statistically, that is minority. I have not seen a PSU of this type where they were not so replacing them is a must.

DataSheet: DM311

It is the same board under the Sparkle brand. That is under normal operation though, if the DM draws more than 3 mA than it should, there can be higher drop on it than on the resistor.

Previous 1 2 Statistics are great for politicians. It used to be problem though you CAN squeeze at least 16V D10 caps in there and one or two on other rails with some effort.

Hopefully this information helps. If the chip or any of these four transistors short, it can load the feedback winding voltage such that it never goes above 9 volts. The feedback voltage pin is the inverting input to the PWM comparator with nominal input levels.

Than it should be more than 70 V. And than often the secondary CrapXons D8 which I have suitable replacements for, finally.

So you need to replace them all, every time. Typical operation on this power supply, it should reach and maintain 12 volts.